Distance Measuring Using UltraSonic Sensor In LCD Display

Sr Karthiga
8y
6k
0
1

Article

Introduction

In this article I will explain about how to measure distance from any object. It can be easily display in the LCD Screen. We can use in the front door to view the distance of people.

Parts of List

Arduino uno
Ultrasonic Sensor (HC-SR04)
BreadBoard
LCD Screen
HookUp Wires.

Ultrasonic Sensor (HC-SR04)

Figure 1: Ultrasonic Sensor(HC-SR04)

It is used to produce the high frequency sound effect.
It can measure the signal from the sender to the receiver.
The echo to be determined from the object.

Where ever we can fix the Ultrasonic Sensor(HC-SR04)

Hospital for medicine
Industry
Home etc.

LCD Screen

Figure 2: LCD Screen

LCD is Liquid Crystal Display (LCD).
It can have the flat-panel or the electronic display
It is used in hospital, showrooms, buses, railway station, airport, etc.

Connections

Connection from the Ultrasonic Sensor (HC-SR04) to the Arduino board

In the sensor it has the following four pins; they can work under the process of the receiving and the sending of the signal.

Vcc in the Ultrasonic Sensor can be connected to the arduino board of the 5V of Vcc.
Triger in the Ultrasonic Sensor can be connected to the arduino board of the digital pin 12.
Echo pin the Ultrasonic Sensor can be connected to the arduino board of the digital pin 08.
Gnd in the Ultrasonic Sensor can be connected to the arduino board of the Gnd.

Connection from LCD Screen to the Arduino board

The LCD screen can have the following four pins.

The Vcc can be connected to the vcc of the arduino board.
The Gnd can be connected to the Gnd of the arduino board.
The SDA can be connected to the arduinoboard of the analog pin A4 .
TheSCL can be connected to the arduino board of the analog pin A5.

Before uploading the program add the library:

Programming
1. #define trigPin 12
2. # define echoPin 8
3. //Flashing LED on Arduino board
4. # define LEDPin 13
5. //LCD
6. # include < Wire.h >
7. #include < LCD.h >
8. #include < LiquidCrystal_I2C.h >
9. #define I2C_ADDR 0x3F
10. // Define I2C Address where the PCF8574A is
11. # define BACKLIGHT_PIN 3
12. # define En_pin 2
13. # define Rw_pin 1
14. # define Rs_pin 0
15. # define D4_pin 4
16. # define D5_pin 5
17. # define D6_pin 6
18. # define D7_pin 7
20. int n = 1;
21. LiquidCrystal_I2Clcd(I2C_ADDR, En_pin, Rw_pin, Rs_pin, D4_pin, D5_pin, D6_pin, D7_pin);
22. void setup()
23. {
24. Serial.begin(9600);
25. pinMode(trigPin, OUTPUT); //The transmit pin of the ultrasonic sensor
26. pinMode(echoPin, INPUT); //The receive pin of the ultrasonic sensor
27. pinMode(LEDPin, OUTPUT); //The LED of the Arduino
28. lcd.begin(20, 4);
29. //Size of LCD
30. // Switch on the backlight
31. lcd.setBacklightPin(BACKLIGHT_PIN, POSITIVE);
32. lcd.setBacklight(HIGH);
33. lcd.home(); // go home
34. }
35. void loop()
36. {
37. int duration, distance;
38. digitalWrite(trigPin, HIGH);
39. delayMicroseconds(100);
40. digitalWrite(trigPin, LOW);
41. duration = pulseIn(echoPin, HIGH);
42. distance = (duration / 2) / 29.1;
43. lcd.clear();
44. lcd.setCursor(0, 0);
45. lcd.print("Distance from object");
46. lcd.setCursor(0, 1);
47. lcd.print(distance);
48. lcd.print("cm");
49. if (distance >= 15)
50. {
51. lcd.setCursor(0, 4);
52. lcd.print("Safe Zone :)");
53. digitalWrite(LEDPin, HIGH);
54. delay(500);
55. digitalWrite(LEDPin, LOW);
56. delay(500);
57. }
58. else
59. {
60. lcd.clear();
61. lcd.setCursor(0, 0);
62. lcd.print("STEP AWAY!!!");
63. lcd.setCursor(0, 1);
64. lcd.print("STEP AWAY!!!");
65. lcd.setCursor(0, 2);
66. lcd.print("STEP AWAY!!!");
67. lcd.setCursor(0, 3);
68. lcd.print("STEP AWAY!!!");
69. digitalWrite(LEDPin, HIGH);
70. delay(50);
71. digitalWrite(LEDPin, LOW);
72. delay(50);
73. digitalWrite(LEDPin, HIGH);
74. delay(50);
75. digitalWrite(LEDPin, LOW);
76. delay(50);
77. digitalWrite(LEDPin, HIGH);
78. delay(50);
79. digitalWrite(LEDPin, LOW);
80. delay(50);
81. digitalWrite(LEDPin, HIGH);
82. delay(50);
83. digitalWrite(LEDPin, LOW);
84. delay(50);
85. digitalWrite(LEDPin, HIGH);
86. delay(50);
87. digitalWrite(LEDPin, LOW);
88. delay(50);
89. digitalWrite(LEDPin, HIGH);
90. delay(50);
91. digitalWrite(LEDPin, LOW);
92. delay(50);
93. digitalWrite(LEDPin, HIGH);
94. delay(50);
95. digitalWrite(LEDPin, LOW);
96. delay(50);
97. digitalWrite(LEDPin, HIGH);
98. delay(50);
99. digitalWrite(LEDPin, LOW);
100. delay(50);
101. digitalWrite(LEDPin, HIGH);
102. delay(50);
103. digitalWrite(LEDPin, LOW);
104. delay(50);
105. digitalWrite(LEDPin, HIGH);
106. delay(50);
107. digitalWrite(LEDPin, LOW);
108. delay(50);
109. digitalWrite(LEDPin, HIGH);
110. delay(50);
111. digitalWrite(LEDPin, LOW);
112. //That really long repeat is to allow the LED pin on the Arduino
113. }
114. }

Explanation

In this case it can send and receive signal from the ultrasonic sensor, when the object is near it can be displayed in the LCD screen.

When the object is near it can detect the SAFE ZONE message in the LCD screen.

When the object is away it can detect the STEP AWAY message in the LCD screen.

Output

Figure 3:Output